 | Accessories/Equipment/Utility/Wreckers Work Smart. . Play Hard. . Always Look Good!! Toll Free 800-813-0717 Store Hours: Mon-Fri 8:00am to 5:00pm (PST) N. 605 Fancher Rd. Spokane WA |
||||||
|
|
|||||||
some items may be
special ordered
call 800.813.0717 for any items not shown!
| American Made Aerial Equipment | ||
| Skylift Mini-Derrick 33 Plus | ||
|
||
| Track Drive and Wheel Drive available | ||
|
||
| Specifications | ||
| Base | High Strength Steel Construction | |
| Drive | 2 Speed Planetary Reduction | |
| Tracks | Hydraulic Extension, Rubber Construction. | |
| Engine | 3 Cylinder Water Cooled Kubota Diesel | |
| Pump | 10 G.P.M. Gear Design | |
| Hydraulic Tank | 11 Gallon | |
| Max. Operating Pressure | 2750 PSI | |
| Drive System | Full Pressure Full Lever | |
| Boom Assembly | 3 Section All Hydraulic Extension | |
| Insulation | 46 KV Cat. C | |
| Stabilizers | 4 Outrigger/Hybrid Design Radial Type | |
| Rotation | 540 degree/High Strength Bearing | |
| Controls | Full Pressure | |
| Sheave Height | 33 ft. | |
| Capacity | 4000 lbs. | |
| Winch | Planetary/Nylon Rope | |
| Tailer | 12000 lb. GVW Tandem Axle | |
| Key Features: | ||
| Ground Control Station Ground controls are located at the rear of the machine for easy operator access. The controls operate all machine functions: boom elevation, boom extension, turret rotation, winch drive, auger operation, pole claw operation, forward/reverse drives, steering, and outrigger extension. |
||
| Winch A 3000 lb. planetary winch is mounted to the main boom. High strength nylon rope is used for insulating purposes. |
||
| Earth Auger A hydraulically driven auger package PERMANENTLY attaches to the telescopic boom assembly for the installation of poles (auger and auger drive can be removed if required). The planetary auger drive can deliver up to 2500 foot-pounds of torque. An 18 inch auger is standard with the unit; however, other sizes are available as options. |
||
| Hydraulic Tool Outlets Hydraulic tool outlets, controlled by a switch at the control station, are provided at ground level. |
||
| HOP (Hydraulic Overstress Protection) The HOP system is a fully hydraulic system (no electrical connections) which protects the machine and operator from exceeding the working limits of the machine, thereby reducing the risk of tip-over or mechanical damage. When the working limits of the machine are exceeded, the HOP system will not allow the winch to be raised. In addition, the following boom functions are also blocked:
| ||
| Pole Carrier Brackets (optional) Two pole carrier brackets are mounted to the frame and quickly detach by removing a pin and sliding the carrier out of its mounting bracket. The mini-derrick easily transfers a utility pole from the trailer to the base-mounted brackets and carries the pole to job site. |
||
| Remote Radio Controls The remote radio controls feature a full feathering, single-hand-held transmitter with 5 switches and a proportional trigger. The controls, which operate within a 350 foot radius of the machine, operate all primary boom functions and steering & drive controls. |
||
| Personnel Bucket (optional) The 2' x 2' x 4' fiberglass bucket with liner and manual brake can easily be pinned and unpinned from the fiberglass boom tip. |
||
| Pole Guide (optional) The hydraulic pole guide has multiple angle positions and is removable. |
||
| JIB (optional) A detachable fiberglass jib includes HYDRAULIC angle adjustment. The jib length can be manually adjusted by simply removing a pin and sliding the jib in or out. The optional jib boom offers a total 41 feet of sheave height. The jib is ideal for hanging TRANSFORMERS on poles up to 45 feet high. |
||
| Optional Equipment | ||
|
||
| E-Mail | Contact Us | Galleries | Location/Map | About Us | Employment |
